聯系我們
18560023440
王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間
新聞資訊
保麗龍雕刻機常見的問題的解決方法
來源：http://www.hejixiang.com 時間：2020-10-26
保麗龍雕刻機在日復一日的工作過程中難免會出現一些問題，有些原因是因為機器本身配置的問題，有些原因則是由于客戶誤操作造成，下面墨源就一些常見的問題做了一些整理，以供大家參考：
In the process of working day after day, some problems will inevitably appear in the process of polylon engraving machine, some of which are caused by the configuration of the machine itself, and some of the reasons are caused by the wrong operation of customers. The following ink source has done some sorting on some common problems for your reference:
一：保麗龍雕刻機工作過程中主軸電機突然停轉或轉慢。
1： The spindle motor suddenly stops or slows down during the working process of styrofoam engraving machine.
原因：
reason:
1、 工作電壓不穩或超負載，加個穩壓器即可。
1. Working voltage instability or overload, add a voltage regulator can.
2、 檢查中間線是否接好，線頭是否有脫焊。
2. Check whether the middle line is well connected and whether the wire end is desoldered.
墨源數控采用先進的裝配工藝，每臺出廠的機器都經過72小時高強度的質檢測試，確保機器0故障，同時及時的售后服務團隊也一時間幫助客戶解決機器使用過程中出現的故障，確保客戶的是生產精度不受影響。
Ink source CNC adopts advanced assembly technology, each machine has passed 72 hours of high-intensity quality inspection test to ensure that the machine has no fault. At the same time, the timely after-sales service team also helps customers solve the problems in the process of using the machine, so as to ensure that the production accuracy of customers is not affected.
二：保麗龍雕刻機不能在原點雕刻。
2： The styrofoam engraving machine can't carve at the origin.
原因：
reason:
1、 文件的版面大小是否與機器匹配。
1. Whether the layout size of the file matches the machine.
2、 檢查是否設有偏移量（OFFSET），版面設置是否正確。
2. Check whether offset is set and the layout is set correctly.
三：保麗龍雕刻機啟動復位時發出異常聲響或總是頂壞限位開關
3： Baolilong engraving machine makes abnormal sound when it starts to reset or always breaks the limit switch
原因：
reason:
1、頂不到限位開關，把其較正即可。
1. If it can not reach the limit switch, just align it.
2、驅動線接觸不好，驅動線固定即可。
2. If the drive line is not in good contact, the drive line can be fixed.
3、限位開關線沒接好，把線接好即可。
3. If the limit switch wire is not connected well, just connect it.
4、限位開關損壞，換之即可。
4. If the limit switch is damaged, replace it.
四：保麗龍雕刻機設置原點時有時向前偏移或向右偏移且偏移距離不定。
4： Styrofoam engraving machine set the origin sometimes forward or right offset and the offset distance is uncertain.
原因：
reason:
1、 限位開關失靈，在系統回到系統原點的過程中限位開關已閉合又彈開。換限位開關即可。
1. The limit switch fails. In the process of the system returning to the system origin, the limit switch has been closed and opened. Replace the limit switch.
2、 驅動線松動。設法把其固定緊即可。
2. The drive line is loose. Try to fix it tightly.
通過小編本文的講解，希望可以幫助到您，如需更多的精彩內容請關注公司網站：http://www.hejixiang.com
Through the explanation of this article, I hope it can help you. If you need more wonderful content, please pay attention to the company's website: http://www.hejixiang.com
- 上一篇：保麗龍雕刻機的操作擁有哪些功能？
- 下一篇：五軸保麗龍雕刻機與四軸保麗龍雕刻機的區別
